Replacing uPVC Window Handles
The replacement of window handles made of upvc is an easy job. The most important thing is to ensure that the new handle is a good fit for the spindle that was cut out of the window mechanism.
If you follow the steps below any cockspur handle can fit in most windows. The step height of the handle is crucial.
What to Look for
Over time, uPVC handles on many windows in the UK may begin to show signs wear and wear and tear. The window handle may become loose or difficult to operate when this happens. This is a relatively simple task that can be completed by anyone who is comfortable using basic hand tools.
The first thing to do is make sure that the handle is securely attached to the window frame, and is in a position that is open. The next step is to locate the fixing pins or screws that hold the handle in the position it is in. They are usually on the inside face of the handle and can be removed with a screwdriver or pliers.
When the handle is loose It is best to gently pull it away from its hinges. Then, you'll need to locate a new handle that is the same style and size. This can be done in the DIY store or on the internet. The process should take about five minutes and a screwdriver is all you need.
The most important thing to consider when replacing the uPVC window handle is the step height. This is the distance between the handle's base and the place it is located within the frame of the window. This is typically an accepted measurement, however it is crucial to examine the step height of your existing handle prior to ordering an entirely new one.
There are several sizes depending on the type of handle. Inline handles for uPVC windows usually feature lug centers of 31mm, and there are also cockspur handle types with 43mm centres. Tilt and turn handles are often found on windows made of uPVC and they have a special design that allows windows to be slid up for ventilation and turned to open the window completely.
The most common uPVC handle breakage is internal cracking, instead of a break at the base. This can make them hard to open and is why it is crucial to ensure that the replacement handle you purchase has the same spindle length as your existing one.
Remove the Old Handle
Incorrectly installed or damaged window handles may cause your double-glazed windows to open or close incorrectly, and can result in them becoming stuck. There are many reasons, such as general wear and tear or corrosion of the handle made of metal. In these situations it is essential to locate replacement window handles made of upvc as soon as you can in order to prevent further damage and loss of functionality.
When replacing upvc windows handles, you should remove the old handles from the window. Start by removing the screw when the handle in closed position. After you have removed the screw, you can take off the handle. It is a good idea to employ an electric screwdriver to accomplish this, as it makes the task easier and quicker.
It is also important to note that the screws on the handle may be hidden behind caps made of plastic, so it is a good idea to use a Stanley knife to the screw caps and then remove them. Once the old handle is removed, you must look at the square cut on the handle's base to make sure that the new window lock handles are compatible with it. This is important because you'll need to determine the length of the spindle on the previous handle to make sure it is the same size as the window mechanism and the handle spindle that has been cut out.
The various types of window handles made from upvc include: Espag handles, which feature a central screw that can be turned left or right; Cranked handles which have two screws and are used on tilt and turn upvc windows and Spade handles that have an arm that is flat and can be put on either side of the window. Once you have found a suitable replacement, it is simply a case of screwing the handle into place and ensuring that the spindle is correctly placed into the lock mechanism. Once that is done the handle should be secured to the window frame and your replacement window handles made of upvc should be secure.
Take a measurement of the Spindle
If you're looking to replace a handle made of upvc that has fallen, it's likely the spindle holding it in place is damaged or is loose. In some instances you can tighten the spindle with a screw or pin. In some cases it might be necessary to replace the handle. There are a few different types of upvc window handles. They include espagnolette handles inline or cockspur handles. They also have tilt and turn handles. Each kind has a distinct method of installing and replacing the handle.
upvc door handle is essential to measure the current handle before purchasing an alternative. This will ensure that the handle fits the window properly and will be of the correct size. Fortunately, all handles follow industry standard sizing so it's relatively easy to identify the right size.
To measure the handle's size, turn the window to the open position. Then, you should be able to see the size of the screw or pin that is holding it. Then, use a ruler or tape measure to determine the length of the spindle. Once you have determined the length of the spindle, you can purchase a replacement one that is exactly the same size.
When purchasing a replacement, it is important to be aware of the step height of the upvc window handle. The step height is the distance from the base of the handle to the point at which it sits on the frame. Typically, this will be approximately 21mm for uPVC windows and 9mm for aluminum. Dropping something into the gap will let you determine how far the handle extends before it reaches an obstruction.
Cockspur handles may have different backsets depending on what type of window you put them in. Inline espag handle heights are 43mm from centre to centre (two fixing points). Cockspur handles have different backsets based on the window they are placed in. This is due to the fact that they have a spur which extends from the handle and is locked onto a cockspur wedge striking plate.
Install the new handle
After you've chosen the new handle, ensure that it is aligned with the screw holes on the door. Secure it using the screws supplied. Install the latch lever the same manner as the handle that you are replacing when you're replacing the door handle. Then, you can attach the door trim once more to conceal the screws for mounting.
Tips: To take the head made of metal from the wooden wedge Hold the handle so that its broad end rests on the floor. Use an hammer to tap the thin end of the handle. Be careful not to scratch the handle or the handle spindle.